Upper Ball Joint

Comparing the upper ball joints shows some obvious design differences. The longer body of the TAS joints offers much better strength and support than the stock version.

Internally the TAS joints have more contact area which spreads out the load and increases the durability.

Tie Rod Ends

As part of the steering system, the main function of tie rod ends is to serve as a flexible coupling point for steering which helps in quicker maneuvering. 

By frequently greasing the part, impurities and debris may be efficiently flushed out. Be sensitive to the signs which indicate that damage is already brewing on the tie rod ends. A worn part normally causes feathering or excessive tire wear.

Idler Arms

The Idler arm is the partner of the Pitman arm, which connects the steering box to the steering gear. The job of the idler arm is to hold the right side of the steering linkage. Between them, the centre link is supported in the proper position so that the left and right wheels work in unison. 

As Idler arms have an integral pivot function it usually makes them more susceptible to wear than the Pitman arms.

Pitman Arm

We also supply versions of every Pitman Arm to exact factory specs. The Buy Auto Parts brand Pitman Arms look, fit, and performs perfectly.

Suit VE-CM equipped with manual steering.

Lower Control Arm Inner Bushes (PAIR)

Suit all models from S series to CM

Complete kit for 2 control arms (sold as a set) These lower inner control arm bushings are the same as the ones included in our popular front end kits.

These rubber bushings are made of much better rubber compounds than the original bushings, and are newly manufactured, not old NOS parts that have been sitting around for 40 or more years.

Every front end rebuild involves the control arms in some aspect, so why not freshen them up to new with a set of control arm bushings? We also offer Upper Inner control arm bushings, tie rod ends, ball joints, pin kits, shaft kits, stab links, and king pin sets in our store separately from the front end kit.

Brake Rod Reaction Bar Bushes, Single-Piece

Suitable for use on SV1, AP5, AP6, VC, VE, VF, VG and VH.

Rubber Steering Rag Coupling Repair Kit

Suit all models from AP5-CM. High quality, genuine rubber unit guaranteed to give you a factory road-feel.

Air Cell for Level Control

Level control systems maintain the height of the vehicle as closely as possible to a predetermined level under all load conditions. This constant level allows the suspension system to maintain the alignment geometry. 

The system can be hydraulic or pneumatic, and in the case of a pneumatic system we can provide the air cells to keep your system in perfect working order.

Coil Springs

We have the following range of coil springs available: 

8 x 180                                  8 x 450

8 x 200                                  8 x 500

8 x 250                                  8 x 550

8 x 300                                  8 x 600

8 x 350  

Control Arm Bushes

Soft, ageing or failing suspension bushes can cause a range of handling problems. Used to connect the various moving components to your vehicle's chassis, suspension bushes act much like human joints.  

During every journey each suspension bush inevitably takes a pounding. It's no surprise that they need replacing from time to time.

Control Arms

Whether it is FEBI, BAW or HRA, we have the greatest range and quality of control arms for your vehicle to keep your suspension system in the best working order, keeping you safe on the road.

Stabiliser Links

Your stabiliser links connect several parts of your suspension that take much of the punishment as you pass over pot holes and other road imperfections.

We have a full range of stabiliser links available for you.

Strut Mountings

As the name implies, the strut mounting attaches the suspension strut to the vehicle. In addition, these autoparts insulate the tire noise and vibrations from the vehicle. 

When to replace them: 

A simple rule of thumb is that if the struts or coil springs are being replaced because of age or wear, then also replace the mounts. A worn or damaged mount can cause a variety of symptoms, so they should be inspected by a qualified technician. Disassembly of the entire strut & spring assembly is required to remove & replace the mount. 

Therefore replacing all worn components at the same time could save you from doing the work a second time.

Strut Tower Bars

Our range of strut tower bars will minimise the strut tower flex during hard cornering, in turn reducing loss of traction, understeer and tire wear by improving chassis rigidity.

Subframe Kits

A subframe, usually constructed from welded steel tubing and attached to a vehicle unit-body by bolts, houses the engine and the vehicle's steering system.

A component of the vehicle's chassis, subframes run from the front bumper to just under the front seats. 

As a single sub group component of the overall chassis, subframes are quick, easy and inexpensive to replace as well as offering safety benefits in the event of an accident.

We offer a range of  kits covering dozens of applications

Suspension Bushes

Your  suspension bushings serve as protective seals to connection points in your suspension.

To prevent the intrusion of contaminants, bushing kits are used to seal up all connection point to keep them effective and rust-free like new.

However, they will eventually succumb to daily wear and tear, at which time we will be able to provide you with bushes from our extensive range.